This is a forced draft shelter that measures the surrounding temperature and humidity by installing a temperature and humidity transmitter in one ventilation tube.

●The fan motor at the top ventilates at a constant speed so that the temperature and humidity transmitter measurements are the same as those in the ambient air. ●The inside of the tube has a triple structure to block heat, and the tube surface is polished to reduce the effects of solar radiation and other radiation. ●Measurements using the ventilation tube can be performed with either a temperature transmitter or a humidity transmitter, or both. ●Temperature and humidity observations using this device are performed via a separately installed converter equipped with a temperature transmitter and humidity transmitter.

This ventilated psychrometer is a standard for measuring temperature and humidity, and uses a platinum resistance thermometer (Pt100) instead of the conventional glass thermometer.Accurately measures dry and wet bulb temperature and displays air temperature, humidity and dew point temperature.The body is designed to minimize the effects of solar radiation and radiation.

High accuracy measurement using platinum resistance thermometer (Pt100Ω) for dry bulb and wet bulb without using mercury thermometer
Wet-bulb temperature is measured by moistening the non-woven fabric sprinkled on the sensor with the attached dropper.
Calculates and displays dew point temperature (mode switching display)
● Meteorological instrument certification acquisition is possible
● A / D conversion circuit calibration function
● Measurement results are recorded on the microSD card mounted on the main unit.
● Driven by 4 AA batteries (alkaline batteries, approximately 7 hours at room temperature)

The temperature is measured using the characteristics of the resistance change that accompanies the temperature change of the platinum resistance temperature detector.The platinum resistance temperature detector is covered with a stainless steel protective tube, and is installed in a ventilation shelter or a Stevenson screen (with a relay box) for observation.

● High accuracy (JIS class A) and high quality.
● No maintenance is required.
● You can obtain certification from the Japan Meteorological Agency

The temperature is measured using the characteristics of the resistance change that accompanies the temperature change of the platinum resistance temperature detector.The platinum resistance temperature detector is covered with a stainless steel protective tube and mounted on a ventilation shelter for observation.

● High accuracy and high quality.
● No maintenance is required.
● You can obtain certification from the Japan Meteorological Agency
● Waterproof construction.
● 3 wire type can also be used.

The temperature is measured using the characteristics of the resistance change that accompanies the temperature change of the platinum resistance temperature detector.The platinum resistance temperature detector is covered with a stainless steel protective tube and has a completely waterproof structure.It is mainly used for water temperature and ground temperature observation.

● High accuracy (JIS class A) and high quality.
● No maintenance is required.
● Completely waterproof structure.
Water temperature transmitter R900 / ground temperature transmitter R903

This road surface thermometer is embedded in the road surface so that it can be measured in consideration of representativeness.Two transmitters are installed in consideration of damage caused by vibration and the trouble of replacement.

● The mold material of the sensitive part is made of the same material (SB mortar material) as the road surface.
● Designed to be flush with the road surface so that it does not become a traffic obstacle when buried in the road surface.
● The front / rear and 2 sensors are mounted in case of failure.
● The sensory part can obtain the Japan Meteorological Agency temperature test.

By using a platinum resistance thermometer in the sensing part and attaching it to the float, the water temperature at a certain position can be measured from the water surface regardless of the water level.

● The float is designed to be strong against impact and hard to break.
● Surface water temperature can be measured.
● Stable measurement with little secular change.

This water temperature gauge uses a crystal element for the sensitive part, utilizes the characteristic that the frequency changes depending on the water temperature, and transmits the frequency to the receiver on the land part by radio.The receiver demodulates and performs arithmetic processing, analog recording, and at the same time external output.

● There is no hassle of wiring work.
● Even if the water level fluctuates, the water temperature at a fixed position from the surface layer can always be measured.
● Since a crystal element is used, the accuracy is good and there is no secular change.
● A battery alarm is sent.
● Measurable up to 4ch.

This is a humidity sensor that uses a highly accurate and highly reliable polymer film in the detection section. Capacitance change of polymer film with respect to humidity is regarded as change of transmission frequency, and humidity is measured with high accuracy in the whole range of 0 to 100%.

● High accuracy of humidity measurement ± 2% (at 23 ℃)
● Output relative humidity and temperature as serial signals (RS-485)
● Meteorological Agency certification can be obtained (humidity only, temperature is not subject to certification)
● Temperature measurement is possible at the same time (Pt100 sensor)
● Analog output is possible for both humidity and temperature.
● The detector and the main unit can be separated (only the detector can be replaced)

Utilizing the capacity change during water absorption by the polymer thin film, the humidity change is accurately captured and the humidity value is output as an analog signal or RS485.For atmospheric observation, store it in a Stevenson screen or a ventilation shelter to prevent direct sunlight.

● Excellent high accuracy, long-term stability and hysteresis.
● Highly accurate measurement from 0 to 100% RH is possible despite a wide range of specified temperatures.
● JMA certification can be obtained.

The radiant heat of the sun is prevented by putting the thermometer transmitter in a stainless steel triple cylinder and ventilating it.Unlike the Stevenson screen, there are few restrictions on the installation location, and you can measure correctly even when there is no wind.

● Small, lightweight and made of stainless steel.
● Structure with backflow prevention.

Forced ventilation shelter for accurate measurement of outdoor humidity by mounting a capacitance humidity transmitter and dew point temperature transmitter.

● Stable measurement is possible due to forced ventilation.
● Mainly used as a dew point thermometer.

It is used when measuring temperature and humidity, and is a shelter for accurate measurement by preventing the influence of direct sunlight.The thermometer transmitter and hygrometer transmitter compartment have a structure in which multiple circular dishes are stacked to efficiently ventilate the atmosphere naturally.

● No need for power supply due to natural ventilation.
● Easy maintenance due to simple structure.
● Integrated type that can mount a single transmitter for both temperature and humidity.

This instrument is a natural ventilation shelter for measuring temperature or humidity outdoors.It has a structure in which weather-resistant plastic disks with good reflection efficiency and low thermal conductivity are stacked.

● A temperature transmitter, humidity transmitter or temperature / humidity transmitter can be stored inside.
● Highly reflective and low temperature conduction weatherproof plastic material with good natural ventilation
● Ideal for temperature and humidity observation in non-powered areas